Mobile concrete mixing plants china manufacturers
  • Mobile concrete mixing plants china manufacturers

Mobile concrete mixing plants china manufacturers

 to ensure clean the machine and surrounding areas of. 2, the timely removal of accumulated material in the hopper, the sensor normal to zero

Mobile concrete mixing plants china manufacturers Features and Benefits :

Maintenance

1, to ensure clean the machine and surrounding areas of. 2, the timely removal of accumulated material in the hopper, the sensor normal to zero. 3. Check the oil lubrication points adequacy of the gas system in the mist should maintain sufficient oil. 4. Check the electrical, electronics or without overheating, abnormal noise, the instrument indicates whether the normal signal system is intact. 5, regular inspection, adjustment cylinder, valve and solenoid valve, so that the opening and closing to meet the requirements. 6, regularly check the system, such as tainted ash, leakage, oil spills and leakage phenomenon must be promptly treated. 7, mixers and the hopper should be cleaned once every four hours, in order to avoid residual concrete consolidation, impede the normal operation. 8, the class should let go of the air compressor, air tank and filters the water inside, and troubleshoot the operation appears. 9, valve, mixer, solenoid valves, air filters and oil mist, etc. in accordance with the maintenance manual.

Supply and maintenance

1, class work must be carried out before the conveyor belt load inspection, clean up debris, mud stick, fastening various parts of screws, adjust the belt deviation phenomenon, all rotating parts should be flexible rotation. 2. By using the manual electric drum require regular oil changes. 3. Check and top-up for six months after the turning parts of the bearing grease, after an oil change once a year to conduct a comprehensive demolition. 4, Sweepers regularly examine and adjust the frying position close to the belt, to ensure clear material properly. Metering and maintenance 1, the class must check and adjust the weighing hoppers each soft interfaces, there are loose on the length of the holding, to ensure measurement accuracy. 2, after the winter shutdown, should the water supply system, the supply of water in all admixtures drained. 3, additives such as seasonal deactivate the pump must be backwashed to prevent precipitation in the pipeline and pump additive product stick or not solvent.

Stirring maintenance

Mixer maintenance See "JS series twin-shaft mixer Maintenance Manual", but pay special attention to the following points: 1. Check the shaft seal chamber class, import, export and distributor seal piping is smooth, whether full of grease all lubrication points and gear box if there is enough lubricant (grease). 2, each class to observe electric grease lubrication pump oil barrel is used up, near-empty to fill in time, does not allow non-oil operation. 3, class work shift must be fully clean the mixing tube inside and outside, the discharge gate, etc. The product material, and rinse, wash dirty adhesive material to chisel out regularly. 4, a week must be a stirring blade adjustment tightened to prevent accidents caused by falling leaves.

Supply and maintenance

1 week must cement warehouse roof dust means vibrator repeatedly, cleared away the dust bag sticky gray (filter rod), make sure to run the air flow. 2, the inlet duct wall, screw conveyor discharge port must be fully clean up once a week to prevent hard lumps and debris lay a trap and a lack of material failure. 3, a long time without the use of cement required to vent inside the spiral. 4, the outer ball bearing screw conveyor head office, at the central support bearing grease must note once every four hours (WAM screw conveyor without greasing), rear gearbox oil change first time was 500 hours, later replaced annually a grease (lithium grease No. 00)

Please leave a message, our saler will contact you as soon as possible!

  • *Name:
  • *E-mail:
  • Tel:
  • Company:
  • *Country:
  • *Inquiry:
Customer Reviews :
Frequently Questions :

Hot Products

  • Concrete Mixing Drum Concrete Mixing Drum

    1. Concrete mixing tank with Superior performance2. High quality of hydraulic system3. The design of low angle of inclination4. Simple operation and useful application5. Multi types of Chassis Matched

  • Concrete Mixer Truck Concrete Mixer Truck

    1. adopts European modern style2. featuring attractive appearance3. rational structure and stable performance4. different steel materials for different parts of tank body5. Multi types of Chassis Matc......

  • Self-loading Concrete Mixing Station Self-loading Concrete Mixing Station

    1.Equipment Type: Self-loading concrete mixing station2. Model: DS3.53. Productivity: 14m3/hr4. Weight: 7500KG5. Dimension LxWxH: 7.1x2.44x3.3m

Contact Us

Tel: +86-371-86108011
        +86-371-86108022
Fax1: +86-371-86108033
Fax2: +86-371-87575501#812
Mobile: +86-15093371337
Email:sales2@cndasion.com
Address: Dongfeng road, Jinshui zone, Zhengzhou, Henan, China.